DTC P0771 [FN4A-EL]
B3E050219090W33
Diagnostic procedure
STEP
|
INSPECTION
|
ACTION
|
|
---|---|---|---|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related Service Bulletins and/or on-line repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
3
|
INSPECT ATF CONDITION
• Turn the ignition switch to the LOCK position.
• Inspect the ATF condition.
• Is it normal?
|
Yes
|
Go to the next step.
|
No
|
If the ATF color is milky or reddish brown, replace ATF, then go to Step 5.
|
||
4
|
INSPECT ATF LEVEL
• Start the engine.
• Warm up the ATX.
• Is the ATF level within the specification?
|
Yes
|
Go to the next step.
|
No
|
Add ATF to the specified level, then go to Step 7.
|
||
5
|
INSPECT LINE PRESSURE
• Start the engine.
• Measure the line pressure.
Specification Idle: 330-470 kPa {3.4-4.7 kgf/cm2, 48-68 psi} Stall: 1,090-1,250 kPa {11.2-12.7 kgf/cm2, 159-181 psi} (Z6) 1,160-1,320 kPa {11.8-13.5 kgf/cm2, 168-191 psi} (LF)
• Are the line pressures within the specifications?
(See Line Pressure Test.)
|
Yes
|
Go to the next step.
|
No
|
• All ranges: Replace the oil pump or control valve body, then go to Step 7.
• Any ranges: Replace the ATX, then go to Step 7.
(See ATX Workshop Manual FN4A-EL.)
|
||
6
|
INSPECT OPERATION OF EACH VALVE AND EACH SPRING
• Turn the ignition switch to the LOCK position.
• Remove the control valve body.
• Disassemble the control valve body.
• Is each valve operation normal and is the return spring normal?
(See CONTROL VALVE BODY REMOVAL.)
(See ATX Workshop Manual FN4A-EL.)
|
Yes
|
Replace the ATX, then go to the next step.
(See ATX Workshop Manual FN4A-EL.)
|
No
|
Repair or replace the shift valve and return spring, then go to the next step.
(See CONTROL VALVE BODY REMOVAL.)
(See ATX Workshop Manual FN4A-EL.)
|
||
7
|
VERIFY TROUBLESHOOTING OF DTC P0771 COMPLETED
• Make sure to reconnect all the disconnected connectors.
• Clear the DTC from the memory using the WDS or equivalent.
• Start the engine.
• Warm up the ATX.
• Drive the vehicle under the following conditions and make sure that gears shift smoothly from 1GR to 4GR.
• Is the PENDING CODE present?
|
Yes
|
Replace the PCM, then go to the next step.
|
No
|
Go to the next step.
|
||
8
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the "After Repair Procedure".
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
|
No
|
DTC troubleshooting completed.
|