NO.3 WILL NOT CRANK [LF]
B3E010318881W05
Diagnostic procedure
STEP
|
INSPECTION
|
RESULTS
|
ACTION
|
---|---|---|---|
1
|
Connect the WDS or equivalent to the DLC-2.
Do the following conditions appear?
• The engine is not completely started.
• DTC P1260 is displayed.
|
Yes
|
Both conditions appear:
Go to Step 4.
|
No
|
Either or other condition appears:
Go to the next step.
|
||
2
|
Is the coil connector securely connected to the coil?
|
Yes
|
Go to the next step.
|
No
|
Connect the coil connector securely.
Return to Step 1.
|
||
3
|
Does the security light illuminate?
|
Yes
|
Go to the next step.
|
No
|
Inspect the instrument cluster and wiring harness.
|
||
4
|
Connect the WDS or equivalent to the DLC-2 and retrieve DTC.
DTC
B1213, B1600, B1601, B1602, B1681, B2103, B2139, B2141, B2431, U2510 |
Yes
|
Go to appropriate DTC inspection.
(See DTC TABLE [LF].)
|
No
|
Go to the next step.
|
||
5
|
Inspect for the following wiring harnesses and connectors:
• Between coil terminal A and instrument cluster terminal 2Q
• Between coil terminal B and instrument cluster terminal 2S
|
Yes
|
Repair or replace the wiring harness and connector.
|
No
|
Go to the next step.
|
||
6
|
Inspect for the following wiring harnesses and connectors:
• Between PCM terminal 1AI and instrument cluster terminal 1I
• Between coil terminal 1AM and instrument cluster terminal 1K
Is there any malfunction?
|
Yes
|
Repair or replace the wiring harness and connector.
|
No
|
Go to the next step.
|
||
7
|
Inspect the following:
• Battery connection
• Battery condition
• Fuses
Are all items normal?
|
Yes
|
Go to the next step.
|
No
|
Service if necessary.
Repeat Step 7.
|
||
8
|
Is clicking sound heard from starter when the ignition switch is turned to START?
|
Yes
|
Go to the next step.
|
No
|
Go to Step 13.
|
||
9
|
Inspect the starting system.
(See STARTER INSPECTION.)
Is starting system normal?
|
Yes
|
Inspect for seized/hydrolocked engine or flywheel.
|
No
|
Repair or replace components as required.
|
||
10
|
Do any other electrical accessories function?
|
Yes
|
Go to the next step.
|
No
|
Inspect charging system.
(See BATTERY INSPECTION.)
(See GENERATOR INSPECTION [LF].)
|
||
11
|
Connect the WDS or equivalent to the DLC-2.
Retrieve any continuous memory DTCs.
Are there any continuous memory DTCs displayed?
|
Yes
|
DTC is displayed:
Go to the appropriate DTC inspection.
(See DTC TABLE [LF].)
Communication error message is displayed:
Inspect for following:
• Open circuit in wiring harness between main relay and PCM terminal 1BE
• Open circuit in wiring harness between main relay terminal B and PCM terminal 1AT
• Main relay is stuck open.
• Open or poor GND circuit (PCM terminal 1BH, 1AZ, 1BD, 1BC or 1BG)
• Poor connection of vehicle body GND
|
No
|
No DTC is displayed:
Inspect following:
• START circuit in ignition switch
• Open circuit in wiring harness between ignition switch and starter
|
||
12
|
Retrieve any KOEO DTCs using WDS or equivalent.
Are there DTCs displayed during KOEO inspection?
|
Yes
|
DTC is displayed:
Go to the appropriate DTC inspection.
(See DTC TABLE [LF].)
|
No
|
No DTC is displayed:
Inspect the following:
• START circuit in ignition switch
• Open circuit in wiring harness between ignition switch and starter
|
||
13
|
Verify test results.
• If normal, return to diagnostic index to service any additional symptoms.
• If malfunction remains, inspect related Service information perform repair or diagnosis.
|